TOESPACE- Dimensions - Photo Gallery- blanket lift support

SCROLL DOWN FOR IMAGES 

Return to HOME PAGE

TOESPACE BLANKET LIFT - BLANKET SUPPORT - TOESPACE

DIMENSIONS - ASSEMBLY PAGE
​Mr. Big Dog TOESPACE Adjustable Blanket Support
Blanket Support Lift
A Sleep Aid you can depend on!
ToeSpace Tonight.  Feeling Good Tomorrow! 
Contact us: Capricorn Products-Cornerstone
Also email us at:  freedom@toespace.com

DIMENSIONS: ToeSpace is meant to be left extended in place.  It's  always ready.  Your ToeSpace blanket lift bar is  there for you.

 Easy assembly.   

Some parts are pre-assembled.  
 

SHOP NOW - BLANKET LIFTS

BLANKET LIFT - Assembly

  1. Blanket Support Note: Modification of ToeSpace products is done periodically. See Governing Policy.  
     MEASUREMENTS ARE APPROXIMATE

    1.Sections push together making top and bottom bars.
    2. Bottom posts push into corner base. (no longer screw-in)
    3. Side posts adjust by matching pre-drilled holes and adjusting screws.
    4. Top Support Bar pushes down onto side posts.
    5. And, you're done.
    Ready to be inserted.

    Standard Unit width: 21 inches (outside measurement).
    X-Large Unit width: 29  inches (inside measurement -including center extension piece  - 9  inches .) The center extension piece of the unit is purposely left  uncemented for flexibility. The X-large unit can be used with or without  the center piece. Without the center piece in place, the unit is  similar size as standard unit.

    QUICK & EASY ASSEMBLY. No tools necessary.  Portions - partially pre-assembled.  
    1.Push together large Bottom Bar (left and right sides) first. 
    2.Push  in Under Mattress Tubes into each corner section. (Tap in if necessary)  You can easily set the frame on a hard surface to allow you to attach  the top portions. 
    3. Insert the Adjustable Extension Posts (Drilled  holes & screw), into the upright tubes.  Permanent height can be  adjusted later. 
    4. Top Bar (with curved corners): - Push together to  make top bar. Then push sides down over the extension tubes (with  drilled holes). 
    Done. Ready to install under mattress and adjust height to your comfortable height. 

PUSH UNDER MATTRESS TUBES IN BETWEEN BOX SPRING AND MATTRESS. 
1. Drape sheet over top bar 
2. Pull sheet down to bottom bar and clamp. (do not clamp over Coupler). 
3. Top and bottom bars are different thicknesses.
4. With the sheet firmly clamped down, the blankets should stay in place.
5. Adjust for a comfortable height.

         PLACE ORDER NOW!

TOESPACE BLANKET LIFT BAR - adjustments

image7

BLANKET LIFTER ADJUSTMENTS

  • BLANKET LIFT BAR - ADJUSTMENT: 
  •  see pre-drilled extension posts
  •  Adjusts to comfortable height
  • but not too high, keeps your feet warmer.
  • KEEP HEIGHT AT LOWEST LEVEL POSSIBLE.
  • Lift sheet and blankets over ToeSpace
  • Make foot tent over your feet. 
  • Pull sheet over bar down to bottom bar
  • Clamp sheet down over bar.  
  • ToeSpace will support the blanket weight to keep pressure  off your feet and toes.  (Note: the clamp will fit over a sheet and  blanket on top bar.  And, over just a sheet on the bottom bar which is  thicker.
  •  Do not use clamp over couplers.


  • ToeSpace Lift Bar works with or without foot board.
  • MATTRESSES: Fits  most deep mattresses - up to 20 inches. Extension posts allow for 29  inches of total  height from bottom bar to top of blanket support  bar. Mattress thicker than 20 inches, leave seller notation when  ordering.
  • Two width sizes available: 
  •  21 in. wide   and   
  • 29 in. wide. (inside width) 
  • GO TO SHOP CART
  • return to top of page